But que Pass4Test n'offre que les produits de qualité est pour vous aider à réussir le test Cisco 640-802 100%. Le test simulation offert par Pass4Test est bien proche de test réel. Si vous ne pouvez pas passer le test Cisco 640-802, votre argent sera tout rendu.
Le test Cisco 640-802 est une examination de techniques professionnelles dans l'Industrie IT. Pass4Test est un site qui peut vous aider à réussir le test Cisco 640-802 rapidement. Si vous utiliser l'outil de formation avant le test, vous apprendrez tous essences de test Certification Cisco 640-802.
Le test Cisco 640-802 est l'un très improtant dans tous les tests de Certification Cisco, mais c'est toujours difficile à obtenir ce Certificat. La présence de Pass4Test est pour soulager les candidats. L'équipe de Pass4Test peut vous aider à économiser le temps et l'éffort. Vous pouvez passer le test sans aucune doute sous l'aide de notre Q&A.
Choisir le Pass4Test vous permet non seulement à réussir le test Cisco 640-802, mais encore à enjouir le service en ligne 24h et la mise à jour gratuite pendant un an. Nous allons lancer au premier temps la Q&A Cisco 640-802 plus nouvelle. Si vous ne passez pas le test, votre argent sera tout rendu.
Aujourd'hui, il y a pleine de professionnels IT dans cette société. Ces professionnels sont bien populaires mais ils ont à être en face d'une grande compétition. Donc beaucoup de professionnels IT se prouver par les tests de Certification très difficile à réussir. Pass4Test est voilà pour offrir un raccourci au succès de test Certification.
Code d'Examen: 640-802
Nom d'Examen: Cisco (Cisco Certified Network Associate(CCNA))
Questions et réponses: 653 Q&As
Il y a beaucoup de gans ambitieux dansn l'Industrie IT. Pour monter à une autre hauteur dans la carrière, et être plus proche du pic de l'Industrie IT. On peut choisir le test Cisco 640-802 à se preuver. Mais le taux du succès et bien bas. Participer le test Cisco 640-802 est un choix intelligent. Dans l'Industrie IT de plus en plus intense, on doit trouver une façon à s'améliorer. Vous pouvez chercher plusieurs façons à vous aider pour réussir le test.
Aujourd'hui, c'est une société pleine de gens talentueux, la meilleure façon de suivre et assurer la place dans votre carrière est de s'améliorer sans arrêt. Si vous n'augmentez pas dans votre carrière, vous êtes juste sous-développé parce que les autres sont meilleurs que vous. Pour éviter ce cas, vous devez vous former successivement.
640-802 Démo gratuit à télécharger: http://www.pass4test.fr/640-802.html
NO.1 Which three options are valid WAN connectivity methods? (Choose three.)
A. PPP
B. WAP
C. HDLC
D. MPLS
E. L2TPv3
F. ATM
Answer: ACF
certification Cisco 640-802 examen 640-802 640-802 certification 640-802
NO.2 Which command is used to see the path taken by packets across an IP network?
A. show ip route
B. show route
C. traceroute
D. trace ip route
Answer: C
Cisco examen 640-802 640-802 examen
NO.3 Data transfer is slow between the source and destination. The quality of service requested by the
transport layer in the OSI reference model is not being maintained. To fix this issue, at which layer should
the troubleshooting process begin?
A. presentation
B. session
C. transport
D. network
E. physical
Answer: D
Cisco 640-802 640-802 640-802 640-802 640-802
NO.4 Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an
IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts
to ping between the hosts are unsuccessful. What two things can be done to allow communications
between the hosts? (Choose two.)
A. Replace the straight-through cable with a crossover cable.
B. Change the subnet mask of the hosts to /25.
C. Change the subnet mask of the hosts to /26.
D. Change the address of Workstation A to 192.0.2.15.
E. Change the address of Workstation B to 192.0.2.111.
Answer: AB
Cisco examen 640-802 640-802 640-802 640-802
NO.5 When you are logged into a switch, which prompt indicates that you are in privileged mode?
A. %
B. @
C. >
D. $
E. #
Answer: E
Cisco 640-802 640-802 640-802
NO.6 A network administrator must configure 200 switch ports to accept traffic from only the currently
attached host devices. What would be the most efficient way to configure MAC-level security on all these
ports?
A. Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security
mac-address command.
B. Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security
mac-address command.
C. Use the switchport port-security MAC address sticky command on all the switch ports that have end
devices connected to them.
D. Use show mac-address-table to determine the addresses that are associated with each port and then
enter the commands on each switch for MAC address port-security.
Answer: C
certification Cisco 640-802 640-802 640-802 examen
NO.7 Which command is used to debug a ping command?
A. debug icmp
B. debug ip icmp
C. debug tcp
D. debug packet
Answer: B
certification Cisco 640-802 examen 640-802 examen certification 640-802
NO.8 What must be set correctly when configuring a serial interface so that higher-level protocols calculate
the
best route?
A. bandwidth
B. delay
C. load
D. reliability
Answer: A
certification Cisco 640-802 examen 640-802 certification 640-802 640-802
NO.9 Which two addresses can be assigned to a host with a subnet mask of 255.255.254.0? (Choose two.)
A. 113.10.4.0
B. 186.54.3.0
C. 175.33.3.255
D. 26.35.2.255
E. 17.35.36.0
Answer: BD
certification Cisco 640-802 certification 640-802 640-802 640-802
NO.10 Which command displays CPU utilization?
A. show protocols
B. show process
C. show system
D. show version
Answer: B
Cisco 640-802 examen 640-802 examen 640-802 examen
NO.11 Which command would correctly configure a serial port on a router with the last usable host address in
the 192.216.32.32/29 subnet?
A. Router(config-if)# ip address 192.216.32.38 255.255.255.240
B. Router(config-if)# ip address 192.216.32.39 255.255.255.224
C. Router(config-if)# ip address 192.216.32.63 255.255.255.248
D. Router(config-if)# ip address 192.216.32.39 255.255.255.248
E. Router(config-if)# ip address 192.216.32.63 255.255.255.248
F. Router(config-if)# ip address 192.216.32.38 255.255.255.248
Answer: F
Cisco examen 640-802 examen 640-802 640-802 640-802
NO.12 A company implements video conferencing over IP on their Ethernet LAN. The users notice that the
network slows down, and the video either stutters or fails completely. What is the most likely reason for
this?
A. minimum cell rate (MCR)
B. quality of service (QoS)
C. modulation
D. packet switching exchange (PSE)
E. reliable transport protocol (RTP)
Answer: B
Cisco 640-802 examen 640-802 640-802
NO.13 Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C
Cisco 640-802 640-802 certification 640-802 certification 640-802 certification 640-802
NO.14 Your ISP has given you the address 223.5.14.6/29 to assign to your router's interface. They have also
given you the default gateway address of 223.5.14.7. After you have configured the address, the router is
unable to ping any remote devices. What is preventing the router from pinging remote devices?
A. The default gateway is not an address on this subnet.
B. The default gateway is the broadcast address for this subnet.
C. The IP address is the broadcast address for this subnet.
D. The IP address is an invalid class D multicast address.
Answer: B
Cisco examen 640-802 examen 640-802 examen 640-802 examen 640-802 examen
NO.15 If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?
(Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: CE
certification Cisco certification 640-802 640-802 certification 640-802 640-802 examen 640-802 examen
NO.16 Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.
1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2
the native VLAN is not specified.What will happen in this scenario?
A. 802.1Q giants frames could saturate the link.
B. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
C. A native VLAN mismatch error message will appear.
D. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.
Answer: C
Cisco 640-802 640-802 examen certification 640-802
NO.17 Which layer in the OSI reference model is responsible for determining the availability of the receiving
program and checking to see if enough resources exist for that communication?
A. transport
B. network
C. presentation
D. session
E. application
Answer: E
Cisco examen certification 640-802 640-802 examen 640-802
NO.18 The network administrator has asked you to check the status of the workstation's IP stack by pinging the
loopback address. Which address would you ping to perform this task?
A. 10.1.1.1
B. 127.0.0.1
C. 192.168.0.1
D. 239.1.1.1
Answer: B
Cisco 640-802 640-802 640-802 640-802 examen
NO.19 Which protocols are found in the network layer of the OSI reference model and are responsible for
path determination and traffic switching?
A. LAN
B. routing
C. WAN
D. network
Answer: B
Cisco examen 640-802 640-802 640-802
NO.20 Which command is used to load a configuration from a TFTP server and merge the configuration into
RAM?
A. copy running-config: TFTP:
B. copy TFTP: running-config
C. copy TFTP: startup-config
D. copy startup-config: TFTP:
Answer: B
Cisco examen 640-802 examen 640-802 examen
NO.21 The network default gateway applying to a host by DHCP is 192.168.5.33/28. Which option is the valid
IP address of this host?
A. 192.168.5.55
B. 192.168.5.47
C. 192.168.5.40
D. 192.168.5.32
E. 192.168.5.14
Answer: C
certification Cisco certification 640-802 certification 640-802 certification 640-802
NO.22 Which command would you configure globally on a Cisco router that would allow you to view directly
connected Cisco devices?
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
Answer: C
certification Cisco certification 640-802 640-802 certification 640-802 640-802 examen
NO.23 What is the difference between a CSU/DSU and a modem?
A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals
from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals
from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals
from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals
from a router to a phone line.
Answer: D
Cisco certification 640-802 certification 640-802 640-802 certification 640-802
NO.24 Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D
certification Cisco 640-802 640-802 examen 640-802 examen 640-802 640-802
NO.25 Which command is used to configure a default route?
A. ip route 172.16.1.0 255.255.255.0 0.0.0.0
B. ip route 172.16.1.0 255.255.255.0 172.16.2.1
C. ip route 0.0.0.0 255.255.255.0 172.16.2.1
D. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Answer: D
certification Cisco 640-802 640-802 640-802
NO.26 Which command shows system hardware and software version information?
A. show configuration
B. show environment
C. show inventory
D. show platform
E. show version
Answer: E
Cisco 640-802 640-802 examen 640-802 examen 640-802
NO.27 Which command is used to copy the configuration from RAM into NVRAM?
A. copy running-config startup-config
B. copy startup-config: running-config:
C. copy running config startup config
D. copy startup config running config
E. write terminal
Answer: A
Cisco 640-802 examen certification 640-802 certification 640-802
NO.28 A system administrator types the command to change the hostname of a router. Where on the Cisco
IFS is that change stored?
A. NVRAM
B. RAM
C. FLASH
D. ROM
E. PCMCIA
Answer: B
Cisco 640-802 640-802 certification 640-802
NO.29 When configuring a serial interface on a router, what is the default encapsulation?
A. atm-dxi
B. frame-relay
C. hdlc
D. lapb
E. ppp
Answer: C
Cisco 640-802 certification 640-802 certification 640-802
NO.30 When troubleshooting a Frame Relay connection, what is the first step when performing a loopback
test?
A. Set the encapsulation of the interface to HDLC.
B. Place the CSU/DSU in local-loop mode.
C. Enable local-loop mode on the DCE Frame Relay router.
D. Verify that the encapsulation is set to Frame Relay.
Answer: A
certification Cisco 640-802 examen 640-802 640-802 640-802 examen 640-802 examen
La Q&A Cisco 640-802 de Pass4Test est liée bien avec le test réel de Cisco 640-802. La mise à jour gratuite est pour vous après vendre. Nous avons la capacité à vous assurer le succès de test Cisco 640-802 100%. Si malheureusement vous échouerez le test, votre argent sera tout rendu.
没有评论:
发表评论